Home Rewiring in OKC.

Older homes deserve safer wiring. We rewire knob-and-tube, remediate aluminum branch wiring, replace cloth-insulated wire, and upgrade ungrounded outlets across the OKC metro: carefully, with minimal drywall damage, permits pulled, and modern code compliance start to finish.

Old wiring quietly creates risks, until it doesn't stay quiet.

Most rewires we do start with a homeowner noticing one or two of these symptoms. By the time more show up, the situation usually has compounded. Catching it early is the difference between a partial fix and a full replacement.

Knob-and-tube wiring (pre-1950)

That old ceramic-and-cloth wiring in your attic or basement isn’t grounded, can’t safely handle modern loads, and is flagged by most insurers. Replacement is strongly recommended for safety and insurability.

Aluminum branch wiring (1965-1975)

Aluminum used in homes during the copper shortage years has documented fire risks at connections where the metal expands, contracts, and loosens. Remediation or rewiring is needed.

Two-prong (ungrounded) outlets

Older homes often have ungrounded outlets throughout. Modern electronics, appliances, and surge protection all assume proper grounding. The fix may require new wiring or GFCI workarounds.

Warm outlets, burning smell, or scorch marks

Any of these are serious. They indicate loose connections or overheating wiring: both leading causes of electrical fires. Stop using affected outlets and call us today.

Your insurer is flagging your wiring

Many insurance companies won’t write or renew policies on homes with active knob-and-tube or aluminum branch wiring. We can help you address the flag and document the work for your carrier.

Selling and your inspector noted wiring issues

Outdated wiring is one of the most common buyer pushbacks. We can rewire to current code, pull permits, and provide documentation that satisfies inspectors and buyers’ agents.

We've rewired homes across every era of OKC.

The OKC metro has serious older housing stock: 1920s craftsman bungalows near the city core, 1950s ranches throughout Bethany and Del City, mid-century homes in Warr Acres, 1960s and 70s aluminum-wired homes throughout the wider metro. Each era has its own wiring challenges, and we’ve worked on all of them.
Our approach to rewiring is built around three priorities: safety first (modern code, proper grounding, AFCI/GFCI where required), minimal damage (we fish wire through existing cavities, use attic and crawlspace runs, and place patches only where unavoidable), and clean documentation (permits pulled, inspections passed, paperwork for your insurer).
Every rewire is permitted and inspected. We coordinate with insurance carriers when needed and provide written documentation of completed work. Family-owned and serving the OKC metro, and we treat older homes with the respect they’ve earned.
Kelvin Electric electrician upgrades residential electrical panel during rewiring projects

Three steps. No guesswork.

We’ve done enough older-home rewires that we know exactly what to assess up front, and what to communicate clearly before any work starts.

1. Call With a Master Electrician

A master electrician talks with you about your home, the age and type of wiring you know about (knob-and-tube, aluminum, cloth, modern Romex), and any safety concerns, and reviews photos if you send them.

2. Full vs. Partial Recommendation

Not every old home needs a full rewire. Sometimes a partial rewire fixes the actual problem: kitchen, bath, or one wing. Sometimes aluminum can be remediated with CO/ALR or AlumiConn at a fraction of full-rewire cost. We tell you straight which is right, and quote both if applicable.

3. Careful Install, Permit, Inspection

We work in phases that let you stay in the home. We fish through existing cavities, run attic and crawlspace where possible, and patch the minimum needed. Permits pulled with your city, inspection coordinated, and written documentation provided for your insurer.

How Kelvin Electric Pricing Works

No guessing. Here is how pricing works, so you know what to expect before we arrive.

Troubleshooting and Repair: $175

If something isn’t working right, we come out to find and fix it. If we get it done within the first hour, you pay $175 plus any parts. If it will take longer, we stop, explain what we found, and you decide what happens next.

Bigger Projects Start With a Call

EV chargers, generators, panel upgrades, rewires and remodels depend on your home and setup. A master electrician will look over your details and call you, usually the same day and always within 24 hours during office hours (8 to 4), to walk you through the next step.

What's included in every rewire.

A proper rewire is more than pulling wire. It includes the cable itself, all the device boxes, modern outlets and switches with the right protection, AFCI/GFCI where current code requires, the careful access work, the permit, and the paperwork that satisfies your insurer at the end.
Here’s exactly what you get when we rewire your home: included in the quoted scope, with no surprises at the end.

What we replace, and how we do it.

Older homes have different wiring depending on when they were built. Each type has its own approach. Here’s what we work on most.

Knob-and-Tube Replacement

Pre-1950 Homes
Ceramic-and-cloth wiring runs replaced with modern Romex. Full replacement is typically recommended: partial fixes can leave isolated knob-and-tube circuits insurers won’t accept.

Aluminum Branch Remediation

1965-1975 Homes · CO/ALR or AlumiConn
Rather than full rewires, aluminum can often be made safe with CO/ALR rated devices or AlumiConn connectors at every outlet, switch, and junction. Cost-effective alternative to full replacement.

Cloth / Fabric Wire Replacement

1940s-1960s Homes
Old fabric-insulated wire (no grounding wire, brittle insulation that crumbles with age) replaced with modern grounded Romex. Often paired with panel upgrades in the same project.

Ungrounded Outlet Upgrades

Any Older Home
Replacing 2-prong outlets with proper grounded 3-prong outlets: sometimes requires new wiring, sometimes GFCI protection at the start of an old circuit can satisfy code. We tell you which applies.

Partial Rewires

Kitchen · Bath · Addition
Targeted rewires when a specific area is being remodeled or has specific problems. Lower cost than full rewire, common when the rest of the home’s wiring is acceptable.

Full Home Rewires

Whole House · 5-10 Days
Complete replacement of all branch wiring throughout the home, every outlet, every switch, every junction. Often paired with panel upgrade. The full reset for older homes.

Old wiring doesn't fix itself.

We don’t sell fear, but we also won’t sugarcoat what older wiring does over time. Insulation crumbles. Connections loosen. Loads exceed what the wire was designed for. Small symptoms become bigger problems. And the cost of waiting almost always exceeds the cost of addressing it on your schedule.
Here’s what aging wiring actually costs you over time.

Cost of Doing Nothing

Modern wiring changes how your old home works.

A proper rewire isn’t about making your home feel new. It’s about making it work like a modern home should, while keeping the character that made you love it in the first place. Once the wiring is current, everything you’ve been putting off becomes possible.
Here’s what your home looks like after we’re done.

After Your Rewire

Often paired with a rewire project.

Panel Upgrades

Older wiring often comes with older panels. We frequently rewire and upgrade the panel as a single project: code-compliant from service entrance through every outlet.

Surge Protection

Modern rewires support modern protection. Panel-mounted whole-home surge protection guards every appliance and electronic from grid fluctuations.

Smoke Detector Installation

Modern code requires hardwired, interconnected smoke detectors. We install them during rewires as a code-compliant upgrade to old battery-only units.

Common questions older home owners ask.

Don’t see your question? Call (405) 267-7760 and we’ll give you a straight answer.
How does Kelvin Electric charge for troubleshooting, repairs and quotes?
Troubleshooting and repair is $175, plus any parts, and we aim to fix the problem within the first hour. If it looks like the job will run past an hour or is more than a quick fix, we stop, explain what we found, and you decide what happens next. Bigger projects start with a call from a master electrician, and there is no charge for the quote.
How much does home rewiring cost in Oklahoma City?
Aluminum wiring remediation using CO/ALR or AlumiConn connectors is significantly less. We start with a call from a master electrician and give you a clear, all-in quote before any work begins. See how Kelvin Electric pricing works on this page, or call (405) 267-7760 for a quote.
How long does a whole house rewire take?
Most whole-house rewires take 5 to 10 working days depending on home size and complexity. Partial rewires (kitchen or bath only) can be done in 2-4 days. Aluminum branch wiring remediation using approved connectors typically takes 1-2 days. We work in phases to minimize disruption. You can usually stay in the home throughout.
How much drywall damage will there be?
We use fishing techniques, attic and crawlspace runs, and existing wall cavities wherever possible to minimize cutting. Some access holes are inevitable. We coordinate locations to make patching easy and clean. Most rewires require small patches near outlets, switches, and junction points rather than full wall demolition. We can also coordinate drywall repair if you'd like a one-stop project.
Can I stay in my home during the rewire?
Yes: almost always. We work in phases, room by room or circuit by circuit, so power is only off in the area we're actively working in. Power to the rest of the home stays on. Most families stay in their home throughout the project with minimal disruption.
Do I need a permit for home rewiring?
Yes. Every rewire, full or partial, requires an electrical permit from your city or county. We pull every required permit and coordinate inspection. The permit fee is included in our quote. Unpermitted rewires can void your homeowner's insurance and create serious problems at home sale time.
Is knob-and-tube wiring dangerous?
Knob-and-tube wiring isn't automatically dangerous, but it's no longer up to modern standards. It can't be properly grounded, isn't designed for modern appliance loads, fabric insulation degrades over decades, and many insurers won't write or renew policies on homes with active knob-and-tube. Replacement is strongly recommended for safety, insurability, and home value.
What about aluminum branch wiring from the 1960s and 70s?
Aluminum branch wiring used in homes built from roughly 1965-1975 has documented fire risks: primarily at connections where aluminum expands, contracts, and loosens over time. Full rewiring isn't always required; CO/ALR rated devices or AlumiConn connectors at every connection point can remediate the problem at a fraction of full-rewire cost. We assess and recommend the right approach.
Do I need a full rewire or just a partial?
Honestly, it depends on the home. Knob-and-tube usually needs full replacement (insurers don't like partial). Aluminum can often be remediated with connectors. Specific problem areas (kitchen during a remodel, one bad circuit) can be addressed partially. The call with a master electrician lets us understand what's actually there and recommend the right scope.
Will my insurance company accept the work?
Yes. We provide written documentation of completed work: scope, permit number, inspection sign-off, materials used. Most carriers accept this documentation to remove wiring-related underwriting flags. If your carrier has specific requirements, let us know during the inspection and we'll make sure our documentation meets them.

Modern wiring. Same home.

Request a call from a master electrician. We’ll check your panel, look at the accessible wiring, identify what’s there and what needs attention, and give you a straight, all-in quote: partial or full, with no pressure either way.
Scroll to Top